(866) 202-8388
 
M-F: 8:30 am to 5:00 pm (EST)
Closed Weekends

Watts OneFlow In Line Anti-Scale System - 4 gpm - OF140-4

• Manufacturer: Watts
• Brand: OneFlow®
• Model: OF140-4
• Maximum Flow Rate: 4 gpm
• Pipe Connection Sizes: 3/4" FNPT
• Dimensions: 26" (H) x 9-13/16" (W) x 8-5/8" (D)
SKU: S0002150 ( OF140-4 )

Availability: Factory / Manufacturer Direct

$699.99
Details
Product Details
About Watts OneFlow Anti-Scale System
The OneFlow® Anti-Scale System provides protection from scale formation on internal plumbing surfaces. The OneFlow® system is a single cartridge-based system that may be installed on a cold water line prior to a water-using device (water heater, hot-beverage system, appliance, steamer etc.) that requires protection from the ill effects of hard water. OneFlow® prevents scale by transforming dissolved hardness minerals into harmless, inactive microscopic crystal particles. These crystals stay suspended in the water and are passed to drain thereby having a greatly reduced ability to react negatively like dissolved hardness does. The system requires very little maintenance, no backwashing, no salt and no electricity. Typical hardness problems, especially build-up of scale in pipes, water heaters, boilers and on fixtures are no longer a concern. OneFlow® is not a water softener. It does not add chemicals. It is a scale prevention device with proven third party laboratory test data and years of successful Food Service and Commercial applications. OneFlow® is the intelligent scale solution and is a great alternative to water softening (ion exchange) or scale sequestering devices

OneFlow Standard Features
• Chemical free scale prevention and protection - converts hardness minerals to harmless, inactive microscopic crystals making OneFlow® an effective alternative technology to a water softener for the prevention of scale due to water hardness
• Virtually maintenance free - No salt bags or other chemicals to constantly add or maintain
• No control valve, no electricity and no wastewater
• Uses environmentally friendly “green” technology
• Improves efficiency of all water appliances whether heating the water or not
• Simple sizing & installation – all you need to know is pipe size and flow rate
• Perfect system for restaurants, cafeterias and coffee shops where multiple or single equipment protection is desired for longer equipment life and reduced energy consumption
• Inlet ball valve for easy isolation shutoff and filter changes
• OneFlow® does not remove the essential minerals in water that are linked to good health
• OneFlow® cartridge-based systems are easily maintained; change the cartridge once per year

OneFlow Standard Specifications
A OneFlow® scale prevention system shall be installed on the cold water service line to condition the tap water just prior to the service line feeding the equipment it is designed to protect. The system will be sized for maximum or peak flow rate based on the specification of said equipment. A OneFlow® system may also be installed to protect multiple pieces of equipment from the ill-effects of hard water scale provided the aggregate peak flow rate for each piece of equipment it is protecting has been considered. The system shall be plumbed with a bypass valve to allow isolation of filter housing to allow the bypass of untreated water in the event that service or cartridge replacement be necessary. The installation area should be suitable in size for the housing to be serviced without encumbrance and the system should be installed per the Installation, Operation & Maintenance manual as provided with each system.The OneFlow® system must not require additional waste water to backwash, flush, or regenerate once put into service. The system shall not require any chemical additives and shall not require electricity for operation.

Product Note: Copper lines need to be passivized for a minimum of 4 weeks before placing unit into service. Not for use on closed loop systems

Feed Water Chemistry Requirements for OneFlow Systems
• pH Levels - 6.5-8.5
• Hardness (maximum) - 75 grains (1282 ppm CaCO3)
• Water Pressure - 15 psi to 100 psi (1.03 bar to 6.9 bar)
• Temperature - 40°F to 110°F (5° to 43°C)
• Free Chlorine - < 2 ppm
• Iron (maximum) - 0.3 ppm
• Manganese (maximum) - 0.05 ppm
• Copper - 1.3 ppm
• *Oil & H2S - Must be Removed Prior to OneFlow
• Poly-phosphates - Must be Removed Prior to OneFlow
• Silica (maximum) - 20 ppm**

Warning *High levels of Copper will foul OneFlow media and typically originates from new Copper plumbing. Wait a minimum of 4 weeks before placing system in operation. Avoid applying excess flux on the inner surfaces of the pipe and to use a low-corrosivity water soluble flux listed under the ASTM B813 standard.NOTICE** OneFlow media does not reduce silica scaling. Silica can act as a binder that makes water spots and scale residue outside the plumbing system difficult to remove. This 20 ppm limitation is for aesthetic purposes.

PRODUCT NOTICE **OneFlow media does not reduce silica scaling. Silica can act as a binder that makes water spots and scale residue outside the plumbing system difficult to remove. This 20 ppm limitation is for aesthetic purposes.
Additional Info
Additional Info
OneFlow System Type In Line System
Flow Rate (GPM) 4 GPM
Water Quality Product Type Filtration Systems
Brand Watts OneFlow
SKU S0002150 ( OF140-4 )
Stock Status Factory / Manufacturer Direct
Other Products
View Product Technical Guides

Frequently bought together

Customers who bought this product also commonly purchased the following combination of items.